Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
How do you really feel about How to Install a Bathtub?
Installing a bath tub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard job. If the old tub is readily obtainable, the project can relocate easily; if you need to open a wall to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub and also set in the new one. Make sure you have actually qualified yourself for the work and are comfortable attempting it. Rather than employing a professional to take over a halfway-completed task, it is much better to think about employing one before you start. Chances are you might need a specialist plumber to make tube connections.
This short article will certainly help you set up a new bath tub in your restroom if you have already purchased a new tub and do not need to transform the setup of your previous supply of water pipelines.
Your tools as well as product list must consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome due to the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to going on to fit the new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and also the sink. Protect the faucet in place with the maker supplied backnut. When the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The former kind ought to be connected to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub until the spirit level reviews level.
To mount taps, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water supply and also check all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub as well as likewise check the overflow electrical outlet and the normal outlet for leakages.
Lastly, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the bath tub should wait till the bathtub has been made use of at least once as this will certainly settle it right into its last setting.
Getting ready for the Installation
To start with, the supporting framework provided with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, creating the water to pass through the wall surface between the bathroom and the tiling, leading to problems with dampness and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealer can split relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our section on How to Install a Bathtub Yourself. Thanks a ton for spending some time to read through our piece. Feel free to set aside a second to share this write-up if you enjoyed it. I am grateful for your time. Visit us again soon.
Act before it's late! Report this page